Local plumber and gas fitter for the Sunshine Coast and Moreton Bay. QBCC 15559043.Call Damian direct 0447 655 396
PAGE Tradie Plumbing & Gas
5.0 Stars - Based on 181 User Reviews
PAGE Tradie Plumbing & Gas
5.0 Stars - Based on 181 User Reviews

DIY Plumbing in QueenslandWhat You Can Do Yourself, and What Needs a Licence

Queensland is strict about plumbing. Only a short list of jobs can be done without a licence, and almost everything else has to be done by a licensed plumber. Here's that list, how to do the most common jobs on it, and the DIY mistakes I get called out to fix.

By Damian Hall Plumber & gas fitter, QBCC 15559043

What the Law Says

The QBCC calls the jobs anyone can do "unregulated work". Everything else is regulated, and it has to be done by a licensed plumber or drainer.

You can do these yourself

  • Change a showerhead
  • Replace a domestic water filter cartridge
  • Replace the washer or jumper valve in a tap
  • Replace the washers or rubber seal inside a toilet cistern
  • Replace the cap on a ground-level drain inspection opening
  • Install or maintain garden irrigation downstream of a tap or isolating valve

These need a licensed plumber

  • Fitting or replacing a mixer tap, toilet, basin or sink
  • Moving, extending or repairing water or drain pipes
  • Replacing a hot water system, or its valves
  • Plumbing in a fridge water line or a rainwater tank switch
  • Any work on gas, including cooktops, heaters and LPG cylinders
  • Anything on the sewer or stormwater drains

Even unregulated work still has to meet the minimum standards in the Plumbing and Drainage Act. Source: QBCC.

How to Change a Tap Washer

This is the job most worth doing yourself. It only works on older taps with separate hot and cold handles. Mixer taps use a cartridge instead.

  1. Turn the water off at the isolation valve under the sink, or at the main beside the meter.
  2. Open the tap to let the water drain out of the line.
  3. Prise off the cap on the handle, undo the screw and pull the handle off.
  4. Undo the tap body (the headgear) with a spanner. Hold the tap spout with your other hand so it doesn't twist.
  5. Pull out the old jumper valve and washer, and take it to the hardware store to match the size.
  6. Fit the new one, screw the headgear back in firmly, and refit the handle.
  7. Turn the water back on slowly and check for drips.

If it still drips after a new washer, the seat the washer presses against is worn. That needs re-seating or a new tap, which is a job for a plumber.

Changing a Showerhead

Unscrew the old head, clean the thread on the shower arm, wrap it with a few turns of thread tape in the direction of the thread, and screw the new head on hand-tight plus a little. Look for the WELS star rating on the box. A 3-star head uses far less water and still feels like a proper shower.

The DIY Mistakes I Fix Most

  • Overtightened fittings that crack a tap body, a cistern or a plastic nut, and start leaking a week later.
  • Hardware store flexible hoses fitted to taps and toilets. A cheap braided hose that bursts while you're out can flood a house.
  • Caustic drain cleaner poured into a drain that's blocked further down, leaving a pipe full of chemical for whoever opens it next.
  • A new toilet or vanity fitted without the right fall on the waste, so it drains slowly or smells.
  • DIY gas connections on cooktops and BBQ points. These are dangerous, and I can't issue a compliance certificate for someone else's work.

Why the Rules Are This Strict

The rules exist to keep drinking water clean and sewage out of houses. A cross-connection between the drinking water and a garden hose, an irrigation line or a rainwater tank can contaminate the supply for the whole street. A badly vented drain can pull the water out of traps and let sewer gas inside. Doing regulated work without a licence is an offence, and the QBCC can investigate unlicensed work. The same goes for handymen who do plumbing without a plumbing licence.

For how the water, drains and gas in your home fit together, see my guide to how your home's plumbing works.

DIY Plumbing FAQs

What's legal, and what's worth trying.

Call 0447 655 396

Can I replace my own toilet in Queensland?

No. Installing a toilet is regulated plumbing work, so it has to be done by a licensed plumber. You can replace the washers and seals inside the cistern yourself.

Can I replace a mixer tap myself?

No. Replacing the whole tap is regulated work. On older taps with a separate hot and cold handle, you can replace the washer or jumper valve yourself.

Can a handyman do plumbing work?

Only if they hold a QBCC plumbing licence. Without a plumbing contractor licence, a handyman can't do plumbing for you, even small jobs. You can check anyone's licence on the QBCC website.

Can I do my own gas work?

No. All gas fitting has to be done by a licensed gas fitter, and you should get a compliance certificate when it's finished.

Is it worth fixing a dripping tap myself?

On an older two-handle tap, usually yes. A washer costs a couple of dollars. If the tap still drips after a new washer, the seat inside the tap is worn, and that needs a plumber.

Job's Bigger Than a Washer?

Call or text me and I'll give you a fixed price before I start. Licensed for plumbing, drainage and gas. QBCC licence 15559043.

Call Damian direct0447 655 396
Send your details